Tutorial ESP8266 Control Servo Node-RED MQTT (Mosquitto) IoT #2

Tutorial ESP8266 Control Servo Node-RED MQTT (Mosquitto) IoT #2

Reciente Unknown   6:55:00 p.m.

This time the integration of ESP8266 and the Node-RED platform has been made integrating an actuator in this case a servo controlled by PWM with rotation from 0 to 180 degrees.
From an HMI or SCADA Web creator on Node-Red-Dashboard using as base the MQTT Protocol and pubsubclient library converting the ESP8266 into MQTT Client.

Video Test ESP8266 Control Servo  MQTT Node-Red  IoT #3 

Note: To successfully complete this tutorial you must perform the following tutorials.
Previous tutorials Recommended
icstation.com
Tutorial 1 : Install Lubuntu (Ubuntu)
Tutorial 2 : Installation node red platform
Tutorial 3: Installation Node Red Dashboard
Tutorial 4: Installation Modbus TCP IP in Node Red
Tutorial 5: Installation of Mosquitto Broker MQTT in Lubuntu
Tutorial 6: Program ESP8266 con Arduino IDE
Tutorial 7: ESP8266 and Node-RED MQTT GPIO  # 1


Arduino IDE
The ESP8266 module has been configured as an MQTT client, as subscriber of the "servo" topic, the ESP8266 will receive a value from 0 to 100% and will convert it from 0 to 180 degrees for servo control via PWM by GPIO 02.

Mosquitto MQTT Broker
Previously it has been installed in a computer with lubuntu (Ubuntu) Linux, the server Broker MQTT which performs the management of messages in the network, Mosquitto has been used in this case.

Node-Red
A sequence of nodes has been created to send data from the Dashboard.

                                                          Node-RED-Dashboard

                                                            View Tablet

                            Video Tutorial ESP8266 Control Servo  MQTT Node-Red  IoT #4 

  

Materials 
1 ESP8266 01 
1 Regulator LDV33CV  5 a 3.3V
1 Chip FTDI Serial
1 Servo  Mystery control PWM

Connections

Where to buy?
icstation.com 
ESP8266 01 (ESP 01)

Downloads:
Github  Arduino IDE code ESP8266 MQTT
Github pubsubclient  Library 
Node Red  import code example

References
icstation.com
Tutorial 1 : Install Lubuntu (Ubuntu)
Tutorial 2 : Installation node red platform
Tutorial 3: Installation Node Red Dashboard
Tutorial 4: Installation Modbus TCP IP in Node Red
Tutorial 5: Installation of Mosquitto Broker MQTT in Lubuntu
Tutorial 6: Program ESP8266 con Arduino IDE
Tutorial 7: ESP8266 and Node-RED MQTT GPIO  # 1

node-red-dashboard
Nodered.org
github.com/node-red
Nodejs.org

More Information:

Blog PDAControl  English 

Blog PDAControl   Español 

Youtube Channel:

PDAControl

Tutorial ESP8266 and Node-RED MQTT GPIO (Mosquitto) # 1

Tutorial ESP8266 and Node-RED MQTT GPIO (Mosquitto) # 1

Reciente Unknown   7:41:00 a.m.

To integrate the module ESP8266 with node-red IoT platform has been used MQTT protocol, there are client libraries for esp8266 as MQTT in this case I decided to use the library pubsubclient.

This example will receive Node Red that receives data from the ESP8266 and allow control a LED connected to GPIO 02 from a dashboard created in Node Red Dashboard .

Test Led ESP8266 MQTT Mosquitto Node Red  IoT # 1

Arduino IDE add the pubsubclient library using the search engine libraries or manually by downloading the library and storing it in their respective folder for libraries.

Note: To successfully complete this tutorial you must perform the following tutorials.
Previous tutorials Recommended
icstation.com
Tutorial 1 : Install Lubuntu (Ubuntu)
Tutorial 2 : Installation node red platform
Tutorial 3: Installation Node Red Dashboard
Tutorial 4: Installation Modbus TCP IP in Node Red
Tutorial 5: Installation of Mosquitto Broker MQTT in Lubuntu
Tutorial 6: Program ESP8266 con Arduino IDE


Arduino IDE code
Arduino IDE code performs several steps but definire major, Broker connection with MQTT, function post (send messages) even specific topic and subscribe function (receive messages) even specific topic.
Note: At the bottom of the post code Full IDE arduino

1 .Parameters Network 
Set parameters network  PASSWORD  and SSID is required to have previously installed a MQTT Broker server which performs the function server broker, in this case I use Mosquitto MQTT.

const char* ssid = "##############";
const char* password = "###############";
const char* mqtt_server = "192.168.0.19";

2. Function publish ("topic" message)

 client.publish("event", "hello world");

3. subscribe Function ("topic")
the subscribe function makes a call to the callback function for data reception

  client.subscribe("event");

4. callback function
This function enter 3 personal parameters of the library pubsubclient.h topic, payload (load) and size, performs printing  of the topic and the message, to turn on the LED diode sweeps payload in a specific position to determine the state 1 or 0.

void callback(char* topic, byte* payload, unsigned int length) {
  Serial.print("Message arrived [");
  Serial.print(topic);
  Serial.print("] ");
  for (int i = 0; i < length; i++) {
    Serial.print((char)payload[i]);
  }
  Serial.println();

  // Switch on the LED if an 1 was received as first character
  if ((char)payload[0] == '0') {
     Serial.println("LOW");
    digitalWrite(2, LOW);   // Turn the LED on (Note that LOW is the voltage level
    // but actually the LED is on; this is because
    // it is acive low on the ESP-01)
  } 

 if ((char)payload[0] == '1') {
    Serial.println("HIGH");
    digitalWrite(2, HIGH);  // Turn the LED off by making the voltage HIGH
  }

}

Node Red
1 Node client receiving messages MQTT (subscribe) from ESP8266 through the topic "event" node debugging and debug.
2 Building 2 button "On" "Off" for sending node values MQTT (publish) to ESP8266 topic "event"
3 Node text text output to display status LED diode.
Note: At the bottom of the post code on Github Import Nodes

Design Node Red Dashboard 

Organization Tabbed Widgets and Groups

Visualization Node red Dashboard 

Configure Led ESP8266 MQTT Mosquitto Node Red  IoT # 2

Conections ESP8266

VIDEO : Programming ESP8266 with Arduino IDE

Where to buy?
icstation.com 
ESP8266 01 (ESP 01)

Downloads:
Github  Arduino IDE code ESP8266 MQTT
Github pubsubclient  Library 
Node Red  import code example

References
icstation.com
Tutorial 1 : Install Lubuntu (Ubuntu)
Tutorial 2 : Installation node red platform
Tutorial 3: Installation Node Red Dashboard
Tutorial 4: Installation Modbus TCP IP in Node Red
Tutorial 5: Installation of Mosquitto Broker MQTT in Lubuntu
Tutorial 6: Program ESP8266 con Arduino IDE

node-red-dashboard
Nodered.org
github.com/node-red
Nodejs.org

More Information:

Blog PDAControl  English 

Blog PDAControl   Español 

Youtube Channel:

PDAControl

Installation Mosquitto Broker MQTT in lubuntu (Ubuntu) Linux

Installation Mosquitto Broker MQTT in lubuntu (Ubuntu) Linux

Reciente Unknown   6:10:00 a.m.

That is MQTT ?
In short MQTT is a TCP / IP protocol lightweight messaging, the model is publication - subscriber requires a message broker  which is responsible for directing recipients through a topic  in common.
It is considered to Andrew James Stanford-Clark as the author of this protocol.
More information MQTT Wikipedia.
Official Website: mqtt.org

Application
I believe that this protocol is very practical and is currently implemented in IoT and M2M "machine-to-machine" applications, field application in this case would be sending monitoring and control data between servers, sensors and actuators.

Previous tutorials Recommended
Tutorial 1 : Install Lubuntu (Ubuntu)
Tutorial 2 : Installation node red platform
Tutorial  3 : Installation Node Red Dashboard
Tutorial  4:  Installation Modbus TCP IP in Node Red

Architecture MQTT Protocol 

Broker Mosquitto MQTT
Eclipse mosquitto ™ It is open source, it is a message broker this intermediary MQTT allows the connection of devices.
Official Website: mosquitto.org

Installation of Mosquitto Broker MQTT in lubuntu (Ubuntu) Linux

MQTT to connect devices with Node-red I use mosquitto as Broker, this is an extra complement Node red in the next tutorial installation.

Enter the terminal lubuntu command as root.

Add mosquitto repositories dev

sudo apt-add-repository ppa:mosquitto-dev/mosquitto-ppa 

Update repositories linux

sudo apt-get update

Install broker mosquitto

sudo apt-get install mosquitto

Install development libraries

sudo apt-get install libmosquitto-dev

Installing client MQTT

sudo apt-get install mosquitto-clients

Check that mosquitto is running

sudo service mosquitto status

Ready to have fun ...

Video Install Mosquitto MQTT Lubuntu Ubuntu Linux

Customer tests Mosquitto MQTT in lubuntu (Ubuntu) Linux
Subscriber
Our client is suscruibira the theme or topic  "Sensor_MQTT" meaning that all published messages associated with this topic will be received.

mosquitto_sub -h localhost -t "Sensor_MQTT" -v

Publisher
Our client publish the message "Error Sensor" through the topic "Alert_MQTT"

mosquitto_pub -h localhost -t "Alert_MQTT" -m "Error_Sensor"

Ready to have fun ...

Video Test Mosquitto MQTT in Lubuntu (Ubuntu) linux

References
Tutorial 1 : Install Lubuntu (Ubuntu)
Tutorial 2 : Installation node red platform
Tutorial  3: Installation Node Red Dashboard
Tutorial  4: Installation Modbus TCP IP in Node Red

node-red-dashboard
Nodered.org
github.com/node-red
Nodejs.org

More Information:

Blog PDAControl  English 

Blog PDAControl   Español 

Youtube Channel:

PDAControl